Originally, the travails and travels of rebuilding/restoring (or at least getting it running) a twenty six year old Honda Aspencade 1100. The Goldwing was sold to someone who could do it justice. Its been replaced with a 2000 Honda Sabre 1100.
Sunday, November 7, 2010
Thursday, April 15, 2010
Well, it's been a long hard winter. The last thing I did on the bike was run home winterize it. As the December 19, 2009 storm started I realized that I had no antifreeze in the bike! I'd removed it so I could use the head gasket sealer. The thermostat was also removed. I was hoping that I could keep the bike running long enough to get the antifreeze throughout the engine. We'll have to see.
I spoke to my friend Billy (Earl) a master of all things mechanical about the bike. He said that the last thing to do was tear into the carbs and try to rebuild them. This was reassuring, however, it leaves me at a point where I don't know what to do on the bike. I asked him if he'd be willing to take a look at it and he said sure. That just leaves finding a time to do it.
Monday, September 21, 2009
The first major repair, the starter
The starter came off the bike; the book didn't mention that oil was going to come pouring out of the hole.
I had touched base with firm up on Chinquapin Round Road. that was recommended by both Billy (kuethe) and Lewis (Hartge) on Friday September 18 2009. I took the starter up to them on Monday, Tom told me that the minimum bench charge would be $40, if brushes are needed, about $60. As It turned out when Tom called me back a few ours later he said that he had to re-solder the armature and he'd have to send to Cleveland for the brushes, about $100. I told him to go ahead.
This is the first large repair. While $100 isn't the end of the world, what really counts is the whole tab. I've made it clear to Kari, who is an eternal optimist when it comes to things that she loves, that no matter how much I like the bike, it isn't practical to put more into the bike than it's worth.
I had touched base with firm up on Chinquapin Round Road. that was recommended by both Billy (kuethe) and Lewis (Hartge) on Friday September 18 2009. I took the starter up to them on Monday, Tom told me that the minimum bench charge would be $40, if brushes are needed, about $60. As It turned out when Tom called me back a few ours later he said that he had to re-solder the armature and he'd have to send to Cleveland for the brushes, about $100. I told him to go ahead.
This is the first large repair. While $100 isn't the end of the world, what really counts is the whole tab. I've made it clear to Kari, who is an eternal optimist when it comes to things that she loves, that no matter how much I like the bike, it isn't practical to put more into the bike than it's worth.
Apparently the books aren't always right
When I bought the bike the guy gave me the Clymer Service and Repair manual, thankfully. There are some problems though, I think they assume you have some experience with motorcycle repair. For instance, when I thought I was having trouble with the starter they tell you how to test it but not where to find it!
Which is where their mistake came in. After finding the starter, I found the part in the back of the book where it says that for bikes after 1980 you must remove the engine to remove the starter. I thought that was the end; I would rather perform brain surgery than remove an engine. The instructions for removing the starter for a pre 1980 bike are to drop the exaust and the two bolts that hold the starter and yank the starter out. That is what I proceeded to do.
The problem is that when they work on the bike in the book, it doesn't have crash bars or a fairing. It wasn't too much of a problem removing the crashbars, the problem came when I tried to remove the exhaust pipe. The first of the two bolts that hold the pipe to the rear frame ( I didn't get to try the second bolt) was rusted and I stripped it trying to get it off. This could only happen after removing the left panier. To remove the panier I had to disconnect the light which ran through it. Since I stripped the nut I had to try to remove the bolt that held the bracket that held the pipe, which was a little easier. I then had to loosen the clamp that holds the right and left pipe tie in. This might be common for every mechanic but I'm no mechanic and this all seemed like a long way around the barn.
Which is where their mistake came in. After finding the starter, I found the part in the back of the book where it says that for bikes after 1980 you must remove the engine to remove the starter. I thought that was the end; I would rather perform brain surgery than remove an engine. The instructions for removing the starter for a pre 1980 bike are to drop the exaust and the two bolts that hold the starter and yank the starter out. That is what I proceeded to do.
The problem is that when they work on the bike in the book, it doesn't have crash bars or a fairing. It wasn't too much of a problem removing the crashbars, the problem came when I tried to remove the exhaust pipe. The first of the two bolts that hold the pipe to the rear frame ( I didn't get to try the second bolt) was rusted and I stripped it trying to get it off. This could only happen after removing the left panier. To remove the panier I had to disconnect the light which ran through it. Since I stripped the nut I had to try to remove the bolt that held the bracket that held the pipe, which was a little easier. I then had to loosen the clamp that holds the right and left pipe tie in. This might be common for every mechanic but I'm no mechanic and this all seemed like a long way around the barn.
Wednesday, September 16, 2009
Round two, the work begins, if you can call it work
When I finally got to work on the bike I did what little I knew. When I had the bike running I found that the number 3 cylinder down draft tube was cold, almost icey, when the bike ran. The other tubes were warm if not hot. Ah Ha! That's why it was sputtering and backfiring. Number 3 was dumping raw gas into the exhaust and was igniting at odd times. I pulled the spark plug to test it and see if it was firing.
This is accomplished by removing the plug cap, pulling the plug, inserting it back into the cap and turning the bike over, the plug should spark. The plug didn't spark but I did get a shock off the wire. I called Dad. We had talked about the bike when he had less painful moments, which were few. He felt that the bike was choked up with "varnish" from sitting so long. When I told him the plug wasn't sparking he of course said to look at the plug wires and caps along with the rest of the ignition system. When fiddling with the plug part of the cap had broken off. While fiddling with that and trying to repair it a "screw cup" and "fuse like thing" fell out of the cap, and then a spring fell out. I'd never heard of this. I called Dad, he hadn't heard of it either. I tested the fuse with a multimeter, I didn't get any continuity. I went to Pep Boys, they said that there was usually something inside but that they didnt' have replacements. I went to the Honda Dealer in Crofton and ordered a set of wires and caps. The next day I checked the other fuses and tested the number 1 cylinder plug, it didn't spark either. I called Dad (see the pattern?). I asked, when I pull the plug and test it does it have to be grounded to the bike? He hesitated and said yes he was pretty sure it did. Once grounded all the plugs sparked (these were new plugs I'd bought in the begining of the week). I called and cancelled the order for the wires. While it would be nice to have new wires; I first wanted to make sure I had a running motorcycle before "spiffing" it up with non essential. Now I was back to where I started, a rough running bike with no obvious problems. Dad had suggested, as always, Marvell Magic Mystery Oil. During the sessions I'd been adding MMMO to the oil and gas as well as carb cleaner to the gas. These I thought might be adding to the smoke problem so I tried running it "clean" for awhile, the same result was whitish blue smoke. Where to go next?
This is accomplished by removing the plug cap, pulling the plug, inserting it back into the cap and turning the bike over, the plug should spark. The plug didn't spark but I did get a shock off the wire. I called Dad. We had talked about the bike when he had less painful moments, which were few. He felt that the bike was choked up with "varnish" from sitting so long. When I told him the plug wasn't sparking he of course said to look at the plug wires and caps along with the rest of the ignition system. When fiddling with the plug part of the cap had broken off. While fiddling with that and trying to repair it a "screw cup" and "fuse like thing" fell out of the cap, and then a spring fell out. I'd never heard of this. I called Dad, he hadn't heard of it either. I tested the fuse with a multimeter, I didn't get any continuity. I went to Pep Boys, they said that there was usually something inside but that they didnt' have replacements. I went to the Honda Dealer in Crofton and ordered a set of wires and caps. The next day I checked the other fuses and tested the number 1 cylinder plug, it didn't spark either. I called Dad (see the pattern?). I asked, when I pull the plug and test it does it have to be grounded to the bike? He hesitated and said yes he was pretty sure it did. Once grounded all the plugs sparked (these were new plugs I'd bought in the begining of the week). I called and cancelled the order for the wires. While it would be nice to have new wires; I first wanted to make sure I had a running motorcycle before "spiffing" it up with non essential. Now I was back to where I started, a rough running bike with no obvious problems. Dad had suggested, as always, Marvell Magic Mystery Oil. During the sessions I'd been adding MMMO to the oil and gas as well as carb cleaner to the gas. These I thought might be adding to the smoke problem so I tried running it "clean" for awhile, the same result was whitish blue smoke. Where to go next?
Round One... not much of a round
After getting the bike home I started it a couple of times. The first time, I thought I saw white smoke. Doing what I always do, I went to the internet. Yup, blown head gasket. We had a trip planned to go to Wildwood NJ so I really didn't get to play with the bike for about a week. Near the end of our stay I got a call from my father, he said he needed to have a test done; he'd had a couple of these and it shouldn't be a problem, he didn't elaborate. I later found out it was a test for a dysfunctional heart valve. I got a call from my cousin Dianne after the test was done, saying dad was OK but they needed to keep him overnight and he shouldn't do anything strenuous for 24 hours. The problem was that my mother has Alzheimer's and can't stay by herself or really help out around the house. We packed up and went right to my parents condo and staying with dad and mom for the next day and a half.
What's this got to do with the bike? Nothing, that's the point. I had no time to work on the bike. I did manage to start it a couple of more times in the next week. But then I got another call from Dad saying they wanted him in for a heart valve repair or replacement. He was going to go into the hospital on Tuesday August 18, 2009 and get the operation on Wednesday. No problem, we had plenty of time to get ready.
Kari and I wanted to fix some meals so they could be popped into the oven or microwave easily. Randy wanted to drive up I said I could come down and pick him up, which he agreed to. This was probably Thursday August 13, 2009. Then, I think on Friday, Dad called and said that they wanted him in on Sunday for the operation on Monday. I wouldn't be able to pick Randy up on Sunday because I was going to be getting Dad admitted. As imagined, the schedule got very full very quickly. No work on the bike.
Zoom forward about a month. That's really the first time I could really work on the bike. Dad was in the hospital a week. During that time both Randy and I, and on the weekends, Kari were staying at the house with Mom. Randy and I fought about the best way to get mom to bathe and change her clothes. Rather than fighting I let Randy take over. I didn't do this out of meanness. My ways or personality wasn't working with Mom. Dad's recuperation was going to take a long time, Randy could only stay for a week. I decided, I may as well let Randy use his time and efforts to best use. I'd go home at night and let Randy take care of Mom in the evenings. This worked pretty well. Instead of Randy having all the decisions about meals, groceries and bathing made for him, he got to make the decisions. I think this instilled an idea of how difficult the situation was. Randy left and I spent about a week to ten days at Mom and Dad's doing pretty much everything, cooking, cleaning up, laundry, shopping, and driving to the doctors and pharmacy.
What's this got to do with the bike? Nothing, that's the point. I had no time to work on the bike. I did manage to start it a couple of more times in the next week. But then I got another call from Dad saying they wanted him in for a heart valve repair or replacement. He was going to go into the hospital on Tuesday August 18, 2009 and get the operation on Wednesday. No problem, we had plenty of time to get ready.
Kari and I wanted to fix some meals so they could be popped into the oven or microwave easily. Randy wanted to drive up I said I could come down and pick him up, which he agreed to. This was probably Thursday August 13, 2009. Then, I think on Friday, Dad called and said that they wanted him in on Sunday for the operation on Monday. I wouldn't be able to pick Randy up on Sunday because I was going to be getting Dad admitted. As imagined, the schedule got very full very quickly. No work on the bike.
Zoom forward about a month. That's really the first time I could really work on the bike. Dad was in the hospital a week. During that time both Randy and I, and on the weekends, Kari were staying at the house with Mom. Randy and I fought about the best way to get mom to bathe and change her clothes. Rather than fighting I let Randy take over. I didn't do this out of meanness. My ways or personality wasn't working with Mom. Dad's recuperation was going to take a long time, Randy could only stay for a week. I decided, I may as well let Randy use his time and efforts to best use. I'd go home at night and let Randy take care of Mom in the evenings. This worked pretty well. Instead of Randy having all the decisions about meals, groceries and bathing made for him, he got to make the decisions. I think this instilled an idea of how difficult the situation was. Randy left and I spent about a week to ten days at Mom and Dad's doing pretty much everything, cooking, cleaning up, laundry, shopping, and driving to the doctors and pharmacy.
Thursday, September 10, 2009
Subscribe to:
Posts (Atom)